David Barrio

"Home Repair Made Easy"

Category: Appliances

How to Replace a Pilot Light

It can be frustrating when a pilot light on an oven won’t light. You can call Freedom Appliance Repair or another local appliance repair service or attempt to light the flame or replace the light yourself with the tips below:

stove burner

Just as when your oven isn’t going to become hot enough, an oven that’s too hot is typically brought on by a defective thermostat. Now the oven was still a tiny warm from the prior use so I didn’t notice it at once.

To confirm your oven isn’t cooking evenly, it’s possible to also attempt baking a cake or roasting a whole chicken. If you are not able to repair your oven or range with the info above, put in your model number into the search box for extra repair help.

If it isn’t working properly it may be the reason the oven isn’t lighting. In case the oven is just partially cleaned, more cleaning time may be deemed necessary. If your gas-powered Baker’s Pride commercial oven is not functioning correctly, then you’ve come to the correct spot!

Don’t forget to confirm the sort of safety valve you’ve got to receive the proper replacement. There are several different varieties of safety valves. The BASO safety valve may vary in design based on the part of equipment it’s on, therefore it is important that you know the brand name, model and serial number of the bit of equipment to find the appropriate safety valve the very first moment. Under some conditions, you might not smell a propane leak.

In case the appliance has a thermocouple, the issue might be a faulty thermocouple. If you’ve got an appliance that is over 20 years old, have a professional service technician inspect the connector.

Your heating technician will determine when you will need to get a replacement and provide you with one. Get everyone from the house until the issue is corrected by gas company technicians.

“To save some trouble and frustration, you might want to wash the tip of the pilot in the event the light has gone out,” says Bill Donaldson, owner of an appliance repair service in Shelton, CT. The pilots rarely require adjustment. Extinguish the paper immediately after he is relighted.

If it doesn’t, check to be certain the gas supply to the stove is on. Gas ranges certainly have a couple of advantages, including nearly instant heat, long-term cost savings and, clearly, the capacity to continue cooking once the power goes out.

If there isn’t any ability to the igniter circuit, then you need to examine the control board to verify that there’s power at the right output relay. Remove both screws and you find it possible to find the old thermostat control out now.

Both electronic systems will require replacement every couple of decades, so make sure you have regular maintenance scheduled. If you cannot operate any portion of your propane system, or when you feel an appliance or other device is not functioning properly, call your propane retailer or a professional service technician for help.

Replace the gas valve in the event the problem persists. The issue almost always is only a faulty fan oven element. Providentially, it is usually something you can resolve yourself. When it isn’t then you know the challenge really isn’t the igniter.

The very first step in diagnosing a pilot light problem by means of your oven is to be certain that the oven even has a pilot. Parts loosen and wear out with time, and a few are quite simple to repair or replace yourself. The close of the thermocouple is added to the pilot assembly and can just be pulled out.

In the event the light goes out, you want the assistance of a professional service technician. The pilot light is a little open flame that’s fed by a steady stream of gas. It is a small flame inside the device that is lit at all times.

IF it REPEATEDLY GOES OUT or is very difficult to light, there may be a safety problem. Lighting the pilot light on a gas stove is a fairly easy procedure, but working with gas can be dangerous so you ought to exercise caution and get in touch with your community gas company if you observe an extremely strong gas odor.

In most instances, you are going to have to pull the range away from the wall to access the module, which is generally located behind a removable metallic cover on the rear of the range or under a little metallic box under the control panel. The range has to be level to acquire appropriate operating.

Your range was made to be repaired in the house. Most modern gas ranges utilize an electronic pilot igniter to initiate the pilot. Numerous different failures could stop the oven from igniting even though they are not as likely. You receive a call from Mrs. Jones, who doesn’t have a heat.

How to Drain a Washing Machine

washing machine top image

According to Murphy’s law, whatever can go wrong will, and this definitely applies to those ever-important household appliances. One of the things that can go wrong is that your washing machine won’t drain. This can happen for a few different reasons such as a clog of lint or fibers, a kink in the drain hose, or a piece of clothing that made its’ way into the drain pipe.

“If this happens, the first problem that you are going to face is how to get all the water out of it so that you can deal with the problem,” says Tim Nelson, owner of Elite Bloomington Appliance Repair. You may, at first, think that the only way to get this done is to use a bucket and bail out the water. This is the hard way. There is a much better way to handle this issue and we have outlined the steps to help you out.

Steps for Draining a Washer

Cut The Power

Like when you do any repairs or maintenance, you need to make sure that the power is off. Make sure that you switch the power off (if there is an off switch on your machine) and unplug it. Tape the cord to the top of the machine so that you don’t risk getting it wet when you are taking the water out.

Find The Drain and Water Supply Hoses

There are usually three different hoses in the back of the machine. There are the hot and cold-water hoses that are normally color coded red and blue, respectively. The drain hose is normally the gray one among the three. You are going to need to pull the machine away from the wall in order to easily access the drain hose.

Time To Drain The Water Out

There are two possible ways that your machine is going to drain; into a drainpipe in the wall or into a utility sink near the machine. You will need to disconnect the draining end of the pipe from wherever it drains by wiggling it free. You will need to hold it up until you are ready to drain it. If you let the end of the drain hose fall below the water level in the machine, gravity is going to cause it to drain out before you are ready for it. Then you will have a big mess to clean up.

You are going to need to pause the draining process every time that your bucket fills up. You will just need to reconnect the drain pipe into where it is normally meant to drain. Keep doing this until all of the water is drained out of the machine. As the water level gets lower in the machine, you will need to hold the hose lower and lower for gravity to drain the water out.

Unclog The Drain Hose

As you are draining the machine, you may realize that the water is trickling out much slower than it should. This is a good indication that there is a clog in the drain hose. A plumber’s snake is going to easily take care of this for you. To use the plumber’s snake, you will insert the end of the coil until it reaches wherever the blockage may be and then turn the handles on the other end of the snake. This will release the clog. Be ready for water to rush out as soon as this clog is removed.

The Clog May Be In The Drain Pump

You may discover that there is no blockage in the drain hose, which means that it is likely in the drain pump. Drain pumps are located in different areas on different machines and you will need to reference your owner’s manual to know where it is and the safest way to get to it.

After locating the pump, you’ll see that there are a drain hose and an inlet hose that are connected to it. You will release these hoses by taking off the spring clamps that hold them on with a pair of pliers. Then you can locate where the clog is and remove it with a pair of needle nose pliers and then reconnect everything as it was.

© 2019 David Barrio

Theme by Anders NorenUp ↑